Aquadrive Antivibration System
40 years’ experience of installations and aftersales service
- Isolation of the engine from the hull structure
- Cabin & cockpit noise and vibration are greatly reduced by 50% or more
For more information visit Halyard
NOTE: All Images and Tables below will expand when clicked on
Aquadrive Antivibration System – Model Range
CVB 05.10 Aquadrive Moduline B10
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 05 driveshaft is available in lengths from 150 mm (from 240 mm with tubeshaft design).Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B10 Standard version accepts propeller shaft ØA from 20mm (3/4”) to 40mm (11/2”). Oversize version with external clamp mechanism available.
All B10 systems are also available with flange coupling to suit standard BW 5” propeller flange. Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 10.10 Aquadrive Moduline B10
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 10 driveshaft is available in lengths from 150 mm (from 240 mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B10 Standard version accepts propeller shaft ØA from 20mm (3/4”) to 40mm (11/2”). Oversize version with external clamp mechanism available.
All B10 systems are also available with flange coupling to suit standard BW 5” propeller flange. Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 15.10 Aquadrive Moduline B10
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 15 driveshaft is available in lengths from 170mm (from 270mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B10 Standard version accepts propeller shaft ØA from 20mm (3/4”) to 40mm (11/2”). Oversize version with external clamp mechanism available.
All B10 systems are also available with flange coupling to suit standard BW 5” propeller flange. Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 21.10 Aquadrive Moduline B10
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 21 driveshaft is available in lengths from 210mm (from 280mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B10 Standard version accepts propeller shaft ØA from 20mm (3/4”) to 40mm (11/2”). Oversize version with external clamp mechanism available.
All B10 systems are also available with flange coupling to suit standard BW 5” propeller flange. Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 21.20 Aquadrive Moduline B20
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 21 driveshaft is available in lengths from 210mm (from 280mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B20 Standard version accepts propeller shaft ØA from 35mm (11/2”) to 50mm (2”). Oversize version with external clamp mechanism available.
All B20 systems are also available with flange coupling. Contact your local Halyard representative to assist you in selecting a suitable Aquadrivesystem for your application.
CVB 30.20 Aquadrive Moduline B20
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 30 driveshaft is available in lengths from 245mm (from 340mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B20 Standard version accepts propeller shaft ØA from 35mm (11/2”) to 50mm (2”). Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 32.30 Aquadrive Moduline B30
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 32 driveshaft is available in lengths from 300mm (from 420mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B30 Standard version accepts propeller shaft ØA from 40mm (13/4”) to 70mm (21/2”). All B30 systems are also available with flange coupling.
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 42.30 Aquadrive Moduline B30
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 4-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 42 driveshaft is available in lengths from 270mm (from 430mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
B30 Standard version accepts propeller shaft ØA from 40mm (13/4”) to 70mm (21/2”). All B10 systems are also available with flange coupling.
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 42.680 Aquadrive Heavy Duty HDL
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted
power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 5-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 42 driveshaft is available in lengths from 270mm (from 430mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
HDL 680 Standard version accepts propeller shaft ØA from 50mm (2”) to 70mm (21/2”).
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
CVB 42.680 Aquadrive Heavy Duty HDL Flanged
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted
power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 5-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 42 driveshaft is available in lengths from 270mm (from 430mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
HDL 680 Standard version accepts propeller shaft ØA from 50mm (2”) to 70mm (21/2”).
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
HDL 48.690 Aquadrive Heavy Duty – Flanged Option Available
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 5-8° depending on shaft rpm.
Drive Shafts
Custom-length CV 48 driveshaft is available in lengths from 320mm (from 420mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
HDL 680 Standard version accepts propeller shaft ØA from 50mm (2”) to 70mm (21/2”).
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
HDL 60.700 Aquadrive Heavy Duty – Flanged Option Available
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 3° depending on shaft rpm. For higher benching angles please consult Halyard.
Drive Shafts
Custom-length CV 60 driveshaft is available in lengths from 370mm (from 700mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
NOTE: Above does not include Gearbox specific adaptor flange.
Adds approximately 60mm.
Propeller Shaft Options
HDL 700 Standard version accepts propeller shaft ØA from 50mm (2”) to 70mm (21/2”).
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
HDL 60.700 Aquadrive Heavy Duty HT – High Tensile Steel
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 3° depending on shaft rpm. For higher benching angles please consult Halyard.
Also available with 101/2” diameter flange
Drive Shafts
Custom-length CV 60 driveshaft is available in lengths from 370mm (from 700mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
HDL 700 Standard version accepts propeller shaft ØA from 50mm (2”) to 70mm (21/2”).
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.
HDL 60.780 Aquadrive Heavy Duty Flanged
Note: Rating examples are based on optimum conditions with 2° for each CV joints. In case a CV joint will run at an angle greater than 2°, the max permitted power must be reduced (normally by 8-9% for each degree over 2°).
The maximum allowable joint angle is 3° depending on shaft rpm. For higher benching angles please consult Halyard.
Also available with 101/2” diameter flange
Drive Shafts
Custom-length CV 60 driveshaft is available in lengths from 370mm (from 700mm with tubeshaft design). Maximum length depends on shaft rpm.
See Diagrams Below:
Propeller Shaft Options
HDL 780 Standard version accepts propeller shaft ØA from 50mm (2”) to 70mm (21/2”).
Contact your local Halyard representative to assist you in selecting a suitable Aquadrive system for your application.